Reasons Why Your keys nissan Qashqai Key Fob Won't Work

The Qashqai has a distinctly SUV feel to it thanks to its larger dimensions. Moreover, the wheel sizes of 19 inches in Ti and ST-L models may be a bit spongy at times. The front tyres could lose grip on rough surfaces and its CVT can occasionally display wrist-flexing torque steer.

This is typically caused by an unresponsive battery that can be replaced in a matter of minutes. Make sure the new battery is of the same voltage, size and specifications.

Water Damage

One of the most common reasons that a Nissan Intelligent Key Replacement Cost key fob will give the "key ID incorrect" message is due to water damage. The key fob comes with rubber seals which protect the chip inside, however prolonged exposure to moisture could cause it not to function properly. This is typically the case in the event that you've dropped your key fob in the ocean or into a swimming pool, but it can also happen if it gets wet due to rain or soapy hands.

If your key fob has been exposed to water for an extended period of time then you might need to clean it using isopropyl and electronic cleaner. Alternatively, it might need to be taken to a specialist for repair or replacement.

If your key fob has to be replaced, it's quite simple to do. First, ensure that you have a multipack with the correct battery (CR2032 3V). Then open the back and front cases with the small flathead screwdriver. Remove the metal clips, take out the old battery and replace it. Reassemble the fob and replace the mechanical key. Check that it works correctly. If it isn't then you'll need to take it to a Nissan dealer or a professional auto locksmith for replacement of the chip. Fortunately the chip isn't typically damaged by exposure to water and therefore this shouldn't be too expensive.

Dead Coin Battery

Another common reason the reason your Nissan Qashqai key fob might not function is because the coin battery has gone dead. The batteries last for about three to five years, but are prone to failure over time if the fob has been frequently dropped. You can replace the battery, but make sure it is the same voltage and the same size as the previous. If you use another battery, it may cause the key to have an untrue key ID, which will prevent it from connecting to your vehicle.

The best method to replace the battery on a Nissan Qashqai key fob is by removing the fob with an incredibly small screwdriver with a flat head. Push in the screwdriver in an angled notch on the bottom of the fob and twist it gently to split the two parts of the key fob. Then, take out the old CR2025 button cell battery and insert another one after confirming its location on the fob.

Check the terminals for any dirt or water damage prior to installing the new battery. If not clean the terminals using small amounts of isopropyl alcohol. You'll also need to ensure that the pole cables are plugged in correctly - they should be connected to the positive and negative poles of the battery respectively.

Troubleshooting

If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water, it may be an indication of a chip issue inside. You'll need a new keyfob in the event that you can't solve the issue by replacing the battery. If the key fob stopped working after dropping it, it is likely that the chip inside was damaged. It is usually possible to get the key fob back to function again if you take it out and clean the chip using alcohol and paper towels and then insert it back into.

One common error you may notice on the dashboard of your vehicle is "Key ID Not Correct." This means that the car cannot recognize the key fob, and will not allow it to start the engine. The issue could be caused by a variety of factors including water damage, undetectable malfunctions in the circuitry of the key fob or RFID interference.

The key fob will cease to function if the 12 volt batteries are dead or don't provide sufficient electric current. This will affect your Nissan Qashqai's keyless system, central locking and the ability to start the engine with the key fob. If you're unable lock or unlock the door by hand it is recommended to check the batteries on your spare key nissan fob to make sure they are in good condition. You could also try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob had not been submerged in salt water the device should be able to be revived after a quick wash with clean water. You can also clean the electronic chip with isopropyl or electronic cleaner. If these don't work, it may be time to replace the entire key fob by a new one.

If your Nissan Intelligent Key still does not function, there could be a connection issue between it and your vehicle. To reconnect it, start by turning the key in the ignition without starting the car. Continue to do this until the hazard light flashes two times. Then, turn off your vehicle and remove the key.

Next, open the fob compartment in your vehicle. This is usually located in the door jamb, on the driver's side door handle or under the armrest. Find the small button labeled "program" and press it. You will hear a chime when the process is completed.

It's time to test your Intelligent Key to the test. Click all the buttons on the key while standing at a distance from the car. If the lights flash or the horn sounds, then the key is connected to the Nissan. You can also test it near the nissan micra key replacement.